dimensions are shown in mm speci?ations and dimensions subject to change www .ck-components.com contacts copper alloy plating contact area : gold alloy inlay terminals: tin lead (2 min) moldings high temp. thermoplastic ul 94v-0 rated spring stainless steel card detection switch actuator stainless steel number of contacts 8 mechanical life 500,000 cycles min card insertion force 10 n max card extraction force 1 n min / 10 n max contact force 0.25 n min / 0.5 n max card detection switch 0.8 n max for actuation (end travel switch actuation force actuates when card is 1,0 mm from card stop) 1.8 n max for complete depression v ibration fr equency 10 to 500 hz. acceleration 50m/s 2 duration 6 hours - amplitude 0,35 mm max electrical discontinuity 1 s shock peak value 500 m/s 2 Cduration 11 ms 3 shocks in each direction of each axis max electrical discontinuity 1 s insulation resistance 1,000 m min resistance 100 m max curr ent rating 10 ? min / 1 a max dielectric strength 750 vrms min card detection switch normally open contact resistance 100 m max dielectric str ength 250 vrms min curr ent rating 1 ma min / 10 ma max maximum power 0.2 va operating temperature -40c to +85c soldering temperatur e temperature/time pro?e acc. to cecc00802 para. 6.1, fig. 3 with peak temperatur e 250 c damp heat iec 512 test number 11c (10 days) salt mist iec 512 test number 11f (96 hours) card detection switch sealed ip 54 30 per tray, 10 trays per box. 13 ccm02 mk ii the ccm02 mk ii connectors with landing contacts are dedicated for applications where the reader usage is high and the life span of the card is a key consideration. a connector with contacts which land on the card, rather than slide over it, should be speci? ed so as to minimize card wear. the ccm02 has been redesigned to give an even higher performance in a compact, affordable package. features ?500,000 card insertion cycles. ?the contacts do not touch the card until it is almost fully inserted Ca minimal wiping action removes any non-conductive material. ?the connector has been designed to give a positive indication once the card has been fully inserted. ?the reduced size of the contact base saves pcb space, making the connector more stable during surface mounting, and cr eates an air gap between the contacts and card entry slot, which reduces the risk of an electr ostatic transfer to the pcb. ?for added reliability, the integrated card end-travel switch, which is normally open, is sealed against dust and grit. ?by using an inlay nish in the contact ar ea, the life of the pr ecious metal is extended by mor e than 10 times that of standar d gold plating. ?the contact ar ea is spooned to r educe the risk of accidental (or deliberate)damage and to optimize the electrical connection with the card. ?snap--ocks underneath the molding position and hold the connector on the pcb, and give additional support to the contact terminals. ?the plastic moldings are made from a high temperatur e thermoplastic suited for infrared and convection soldering pr ocesses. emv tm is a trademark owned by emvcollc. part number number of termination pcb packaging contacts tails design locating multiple CCM02-2503 8 through hole 4 board lock (pcb 1.6 mm thick) 300 ccm02-2504 8 smt 4 board lock (pcb 1.6 mm thick) 300 ccm02-2508 8 smt 2 pegs 300 ccm02-2511 8 through hole 4 pegs 300 ccm02-2512 8 smt 4 pegs 300 ccm02-2758 8 smt 2 pegs (without cover) 300 ccm02-2763 8 smt 4 boar d lock + 2 pegs 300 ccm02-2765 8 through hole 4 board lock (pcb 1mm thick) 300 ccm02-2766 8 smt 4 board lock (pcb 1mm thick) 300 construction mechanical data contact electrical data switch electrical data environmental data ordering code packaging emv tm compatible
dimensions are shown in mm speci?ations and dimensions subject to change www .ck-components.com 14 dimensional drawings a a (ref.) 50 38,5 52 ? 0,2 a b a 0,95 3,15 19,12 10 b 14 20 7,7 0,3 card entry 4,15 0,3 5,75 15,7 1 0,25 (ref .) 38,5 (ref.) 55,6 1 0,3 a 54,3 5x 2,54 0,65 1,8 4,3 0,2 0,2 0,15 13,8 (ref.) (ref.) 3,2 0,8 0,8 1,6 pcb thickness 6,25 55,6 0,2 13,8 0 -0,3 3,2 +0,4 -0,2 13,8 0 -0,3 4 snap feet embossed channel 10x see detail a 4x 2504 ccm02- xxxx pick and plac e area ?13 designation & date-code area "ccm02" marking is optional coupe a-a card insertion direction card stop detail a pcb layout 27,6 0 -0,6 3,2 20 1,8 10 19,12 21,66 24,2 26,74 29,28 31,82 0 25,3 1,7 52 3,81 3,81 ? 3,2 +0,1 0 ?0,1 1,5 1,5 3,1 14 8,84 1,3 0,2 card end tr ave l switch terminal s 0,8 x 1 contact foot area 0,8 x 1 c1 c2 c3 c4 c5 c6 c7 c8 sw sw (comp onent side) contact location according to iso 7816-2 10x 4x pad plastic outline ccm02-2504 (8 contacts smt - 4 board lock) ccm02-2504 (8 contacts smt - 4 board lock) ccm02 mk ii unless otherwise stated, tolerances are 0,10 mm drawings shown for reference only. for other part numbers please consult your local cannon customer service center .
|
